Dingo Silver

Dingo Silver composed of Portland cement, sand, special chemical additives, and a latex powder for increasing adhesive strength. It is used as a bond coat for setting tiles such as: glass mosaic, porcelain, marble, natural granite, and other larger ceramic tiles, over a variety of substrates for interior, exterior both wall and floor, for swimming pools and wet areas. Dingo Silver meets the requirements for type C2TE according to ISO 13007-1:2010 and TCVN 7899-1:2008.

Categories: Finishing Construction, Tile adhesive, Tiling

Description
Reviews (0)

PRODUCT FEATURES

High quality and durability.
Perfect for tile installation of large porcelain and natural stone tiles.
Can be bonded the large tiles on walls without support needed.
Can be applied on tile over tile.
Suitable for interior and exterior on floors and walls.
Color: White, Grey.

APPLICATION INSTRUCTION

Substrate preparation

All surfaces on which tile is to be set must be dry, structurally sound, free of all grease, oil, dirt, dust, curing compounds, sealers, coating, efflorescence, old adhesive residues, gypsum based underlayment and any other foreign matter.

Proportion of mixing

Dingo Silver Tile Adhesive 25 kg (per bag) per 5.5-6 L of water or 4.5 parts of Dingo Silver Tile Adhesive per 1 part water by volume.

Mixing

Mix Tile Adhesive with clean, potable water thoroughly until smooth with a mechanical mixer at a low speed 150 rpm).
Let mortar slakes for 5 minutes before mixing a second time.
Do not add water, latex, or additional powder after slaking period.

Application

Choose a typical notched trowel that is suitable with each type of tiles. Use flat side of the trowel, applying a film layer of tile adhesive into surface. Apply additional tile adhesive, sweep the surface with notched side of the trowel, held at 60 degrees to create the optimal texture in a single direction.
Place the tiles into the surface, push the tiles back and forth in a perpendicular direction with trowel lines to help achieve maximum coverage and arrange the tiles in place.
Use a rubber hammer to tap lightly on the tiles surface to ensure that the tiles have completely adhered to the tile adhesive.
Remove excess tile adhesive from the joint areas to grouting.
Do not adjust tiles in mortar after they have been set for longer than 15 minutes.

Curing and grouting

A minimum cure is obtained in 24-48 hours, depending on ambient temperatures.
For better quality, Dingo Grout should be chosen to suit each type of tiles. Dingo Grout has many types and color for each joints and places.

TECHNICAL DATA

Test	Type C2TE Requirement	Test result
Adhesion Strength in standard condition	≥ 1.0 N/mm²	Pass
Adhesion Strength after water immersion	≥ 1.0 N/mm²	Pass
Adhesion Strength after heat aging	≥ 1.0 N/mm²	Pass
Open time	≥ 30 phút	Pass
Slip	≤ 0.5 mm	Pass

Choose notched trowel and conpsumtion

Size of trowel	Size of tile	Approximate area (per bag 25kg)
3×3 mm	For mosaic and tiles from 2×2 cm to 5×5 cm	9-10 m²
6×6 mm	For tiles from 10×10 cm to smaller 30×30 cm	6-8 m²
10×10 mm	For tiles, stone > 40×40 cm	2.5-4 m²

Suggestion

Grouting after tile installation at least 24 hours to achieve maximum efficiency.

Limitations

Do not use tile adhesive with wood, asphalt, plastic coat or PVC, metal and mirror.

Caution

Cement may cause injury to skin or eyes.
Use of rubber gloves, dust masks, eye protection, and other safety equipment is recommended.
If contact with eyes occurs, flush immediately and repeatedly with water, and then contact doctor immediately.
Avoid contact with skin. Wash thoroughly after handling.
Keep out of reach of children

Storage

It should be kept in a dry place and the temperature is not too high to avoid product’s degradation. Age of product is 1 year.

Packing

Net weight: 25 kg