PRODUCT FEATURES
- High quality tile adhesive with superior durability and bonding strength.
- Great applied on tile over tile and flexible substrates.
- Able to withstand high compression and vibration.
- Suitable for interior and exterior use on floors and walls, weather resistance.
- Color: White, Grey.
APPLICATION INSTRUCTION
Substrate preparation
All surfaces on which tile is to be set must be dry, structurally sound, free of all grease, oil, dirt, dust, curing compounds, sealers, coating, efflorescence, old adhesive residues, gypsum based underlayment and any other foreign matter.
Proportion of mixing
Dingo Gold Tile Adhesive 25 kg (per bag) per 5.5-6 L of water or 4.5 parts of Dingo Gold Tile Adhesive per 1 part water by volume.
Mixing
- Mix Tile Adhesive with clean, potable water thoroughly until smooth with a mechanical mixer at a low speed 150 rpm).
- Let mortar slakes for 5 minutes before mixing a second time.
- Do not add water, latex, or additional powder after slaking period.
Application
- Choose a typical notched trowel that is suitable with each type of tiles. Use flat side of the trowel, applying a film layer of tile adhesive into surface. Apply additional tile adhesive, sweep the surface with notched side of the trowel, held at 60 degrees to create the optimal texture in a single direction.
- Place the tiles into the surface, push the tiles back and forth in a perpendicular direction with trowel lines to help achieve maximum coverage and arrange the tiles in place.
- Use a rubber hammer to tap lightly on the tiles surface to ensure that the tiles have completely adhered to the tile adhesive.
- Remove excess tile adhesive from the joint areas to grouting.
- Do not adjust tiles in mortar after they have been set for longer than 15 minutes.
Curing and grouting
- A minimum cure is obtained in 24-48 hours, depending on ambient temperatures.
- For better quality, Dingo Grout should be chosen to suit each type of tiles. Dingo Grout has many types and color for each joints and places.
TECHNICAL DATA
| Test | Type C2TES1 Requirement | Test result |
| Adhesion Strength in standard condition | ≥ 1.0 N/mm2 | Pass |
| Adhesion Strength after water immersion | ≥ 1.0 N/mm2 | Pass |
| Adhesion Strength after heat aging | ≥ 1.0 N/mm2 | Pass |
| Open time | ≥ 30 phút | Pass |
| Slip | ≤ 0.5 mm | Pass |
| Transverse deformation | 2.5 – 5 mm | Pass |
Choose notched trowel and conpsumtion
| Size of trowel | Size of tile | Approximate area (per bag 25kg) |
| 3×3 mm | For mosaic and tiles from 2×2 cm to 5×5 cm | 9-10 m2 |
| 6×6 mm | For tiles from 10×10 cm to smaller 30×30 cm | 6-8 m2 |
| 10×10 mm | For tiles, stone > 40×40 cm | 2.5-4 m2 |
Kiến nghị
Để đạt hiệu quả tối đa, chỉ nên tiến hành chà ron sau khi lát gạch tối thiểu 24 giờ.
Khuyến cáo
Không được sử dụng keo dán gạch cho bề mặt gỗ, nhựa đường, nhựa, kim loại và thủy tinh.
Cảnh báo
- Có thể gây hại cho mắt, da và phổi.
- Nên mặc đồ bảo hộ, găng tay, khẩu trang và mắt kính khi thi công.
- Nếu bị dính vào mắt, rửa ngay lập tức bằng nước sạch và đi đến bệnh viện.
- Rửa ngay lập tức với nước sau khi tiếp xúc với da.
- Để xa tầm tay trẻ em.
Lưu trữ
Nên lưu trữ ở nơi khô ráo và nhiệt độ không quá cao để tránh sản phẩm bị giảm chất lượng. Hạn sử dụng 1 năm.
Đóng gói
Khối lượng tịnh: 25 kg/bao
Reviews
There are no reviews yet.